Bersa Forum banner

PISTOL MEDALLION by FreeFire2

873 Views 8 Replies 2 Participants Last post by  SHOOTER13
I am considering offering this stainless steel medallion on this forum and I'd like your comments regarding any interest that you might have.

The investment in the stainless steel material and the cost of the waterjet process to cut them out is significant enough that I must first determine their likelihood to sell.

The medallion itself is 2" tall x 3" long and is cut from 1/16" thick, 300 series stainless steel. There is a loop on the back end of the slide that would allow this to be used on a key ring, a necklace, an ID tag on a range bag or even a zipper pull.

I would offer the medallion without a name in it for $10.00 and the ones with a name would be $15.00. Making them into key rings, necklaces, etc. would add cost to that.

At this point, I am not taking orders rather I am asking to hear from you in regards to your interest. Please feel free to post any questions or comments that you might have.

Thanks!!



See less See more
2
1 - 9 of 9 Posts
I think it's a great idea...

Already want two with my name on it...one as a keychain and one as a range bag zipper pull.

Let me know when you are going to start production...
Thanks, SHOOTER13. I'll be sure and let you know.
Just an update. It has taken me longer to get through the water jet process than I had anticipated. We've had to limit our designs to just the pistol medallion itself without any lettering. I do plan on doing a future run and hopefully we can do lettering then. I will let you know when this first run is available. Thanks for your patience!
Sounds good freefire2 !!
NOW AVAILABLE!! Blanks or Laser Etched



• The medallion itself is 2" tall x 3" long and is cut from 1/16" thick, 300 series stainless steel with a matte finish.

• They are available as blanks or with laser etched printing on one side.

• Laser etching is limited to 12 characters of your choice and will be printed on the side shown**. Both-side printing is available at extra cost.

• Each medallion, blank or etched comes with a beaded chain loop and a key ring.

**Since all etching is custom and done by an outside source, I am limited to the following:

1). Only one font is available and must be the same for all surfaces. The font shown in the picture is the only one currently offered.

2). Due to the set-up cost of the laser, I must accumulate orders for no less than 10 pieces before I have the process done. I will be offering these other places so hopefully that won't take too long.

PRICES
• Blank Medallion . . . . . . . . . . . . $10.00
• Etched Medallion . . . . . . . . . . . $20.00
• Addt'l. for 2nd side etching . . . . $5.00

SHIPPING
• USPS 1st class mail for up to 3 pieces . . . . $3.50

LEAD TIME
• From the time I release the order to the laser to the time I drop your items in the mail is estimated at 7-10 business days.

PAYMENT
• Paypal preferred or USPS money orders

I apologize to you, my customers that this is not a cleaner, easier ordering process. I am probably very much like you; when I order something, I want it and I want it now! I hope that you can endure the wait :)

Thanks!!
See less See more
Awesome my friend !!

As per our last PM...$$ sent for two medallions.

Thanks !!
Thanks shooter. Two medallions headed your way. Thanks again!

Awesome my friend !!

As per our last PM...$$ sent for two medallions.

Thanks !!
I'll let you know when items are received...
1 - 9 of 9 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top